Search results for "Axial force"
showing 10 items of 11 documents
Simplified analytical model for moment–axial force domain in the presence of shear in R.C. members externally strengthened with steel cages
2015
Equations for a hand calculation of moment–axial force domain in the presence of shear for R.C. beam/column externally strengthened with steel angles and strips are developed. The analytical derivation is made assuming, for axial load and flexure, the equivalent stress-block parameters for internal forces, considering the confinement effects induced in the concrete core by external cages both in the cases of strips or angles yielding. Limit states due to bond failure, concrete crushing and yielding of steel angles and strips in flexure and in shear, including moment-to-shear interaction, are considered. The proposed model gives results in a good agreement with available experimental data an…
Moment-Axial Domain of Corroded R.C. Columns
2018
In the present paper, a simplified model to determine the moment-axial force domain of the cross-section of reinforced concrete columns subjected to corrosion process is presented. The model considers members with square and rectangular cross-sections and it accounts for cover spalling, buckling of longitudinal reinforcing bars, loss of bond of bar in tension, reduction of confinement pressures (due to the reduction of the area of stirrups and cracking of concrete induced by rust formation). The analytical expressions for prediction of the area reduction of steel, bond strength and critical load of longitudinal bars utilized were verified against experimental data available literature.
Serviceability and Ultimate Safety Checks of SegmentalConcrete Bridges through N-M and M-V Interaction Domains
2015
In current engineering practice, safety checks on serviceability and determinations of ultimate limit states of segmental bridges built by cantilevering are generally performed, either considering separately the contributions of axial force N, bending moment M, and shear force V, or considering the interaction effects through approximate expressions supplied by building codes. During construction stages and service life, the interaction between internal forces can be of fundamental importance in establishing the actual degree of structural safety and, for this reason, a different philosophy for performing checks in segmental bridges is proposed in this paper, plotting N-M and M-V interactio…
Load carrying capacity of RC compressed columns strengthened with steel angles and strips
2012
Abstract In this paper a comparison between the analytical expressions for the prediction of the load carrying capacity of strengthened reinforced concrete (RC) columns with steel angles and strips is made. Expressions examined consider: the strength contribution due to the confinement effects induced by transverse strips; the composite action due to steel angles and unconfined concrete core; the strength contribution due to the composite actions of angles and concrete core taking into account that steel angles are subjected to axial force and bending moment and concrete core is confined by transverse strips. Design rules given by recent codes for the design of the strengthened columns are …
Theoretical-Applicative Research on Design and Implementation of a Special Dynamometer
2013
The topic of he present paper is taken from the Automotive Systems Nurnberg, Sibiu. It refers to the product automatic gear box which equips a few FORD models, the specific part for which the research was developed being a auto screwing bolt for plastic which raises problems at the robotized screwing because of the poor knowledge of the accurate value of the axial force and the necessary torque.
Influence of column shear failure on pushover based assessment of masonry infilled reinforced concrete framed structures: A case study
2017
Structural frames, constructed either of steel or reinforced concrete (RC), are often infilled with masonry panels. However, during the analysis of the structural frames, it has become common practice to disregard the existence of infills because of the complexity in modeling. This omission should not be allowed because the two contributions (of infills and of frames) complement each other in providing a so different structural system. The use of different modeling assumptions significantly affects the capacity as well as the inelastic demand and safety assessment. In specific, the adoption of equivalent diagonal pin-jointed struts leaves open the problem of the evaluation of the additional…
Moment-axial force domain of corroded R.C. columns
2016
In the present paper, a simple model to determine the moment-axial force domain of the cross-section of reinforced concrete (R.C.) columns subjected to corrosion process is presented. The model considers members with square and rectangular cross-sections and it accounts for—cover spalling; buckling of longitudinal reinforcing bars; loss of bond of bar in tension; reduction of confinement pressures (due to the reduction of the area of stirrups and cracking of concrete induced by rust formation). The analytical expressions for prediction of the area reduction of steel, bond strength and critical load of longitudinal bars utilized were verified against experimental data available in the litera…
Strength and ductility of R.C. columns strengthened with steel angles and battens
2012
Abstract In this paper the behaviour of R.C. members externally strengthened with steel angles and battens subjected to axial force and bending moment is analysed. A fibre model was utilised to predict the moment–curvature diagrams of the strengthened members on the basis of stress–strain curves of the constituent materials (confined concrete, steel bars and angles) recently derived by the author. The stress–strain curves utilised for compressed concrete were able to take into account the confinement effects induced by longitudinal (bars and steel angles) and transverse (stirrups and battens) steel reinforcements. Constitutive laws in compression for confined concrete and steel bars and ang…
Analytical Prediction of the Flexural Response of External RC Joints with Smooth Rebars
2018
Nel presente lavoro viene presentato un modello analitico in forma chiusa in grado di riprodurre la risposta flessionale monotonica di nodi esterni trave-colonna in c.a. con armature lisce. La colonna viene sottoposta a carico verti-cale costante e la trave ad una forza laterale crescente monotonicamente applicata all’estremità. Il modello si basa sul comportamen-to flessionale di trave e colonna adottando un modello di cerniera plasticità concentrata che include lo scorrimento delle armature della trave. Si assume un dominio sforzo normale-momento bilineare semplificato da cui viene derivato il momento ultimo associato alla forza assiale di progetto. Per il nodo viene adottato un modello c…
Investigations on the linear friction welding process through numerical simulations and experiments
2012
Abstract Linear Friction Welding (LFW) is a solid-state joining process applied to non-axisymmetric components. LFW involves joining of materials through the relative motion of two components undergoing an axial force. In such process the heat source is given by the frictional forces work decaying into heat determining a local softening of the material and eventually bonding conditions. In the paper the authors present a designed and assembled laboratory fixture for LFW operations and the results of an experimental and numerical campaign aimed to weld steel parts. The dedicated fixture permitted to highlight the effect of the most important process parameters. Process conditions allowing ef…